Customer reviews from greenworkstools.com
Greenworks - Pro Electric Pressure Washer up to 2300 PSI at 1.2 GPM - Green
Average customer rating
4.6
(1,627 Reviews)
Rating breakdown 1,627 reviews
5 Stars
1,269
4 Stars
245
3 Stars
36
2 Stars
26
1 Star
51
93%of customers recommend this product.
(
1,375 out of
1,471)
Customer Reviews for Greenworks - Pro Electric Pressure Washer up to 2300 PSI at 1.2 GPM - Green
Customer Rating
4
Powerful enough
on January 25, 2022
Posted by: zoopster
from Palmetto, FL
Purchased for basic cleaning around the exterior of the house. Works fairly well for washing cars, cleaning off boats, etc. Delayed start, but I can deal with that. For an electric pressure washer it delivers so far.
I would recommend this to a friend!
Written by a customer while visiting greenworkstools.com
Customer Rating
4
Great Performance for Electric Washer
on March 13, 2022
Posted by: tj5654
from Florida
Gender:Male
I bought the Greenworks 2300 Pro electric pressure washer (5118002VT) late last year. I used it once and stored until I needed it recently. When I first used it, last year, the washer performed well with adequate pressure to clean my heavily soiled concrete driveway. I noticed a lot of water leaking around the hose connector to the unit but thought it might be my hose. This time when I hooked it up I saw the same water leak around the hose connector but had a newer hose connected. Taking it apart I thought the sealing washer caused the leak because the hose wiggled when tightened. I installed a thicker better flexible hose washer but as tight as I could get it the wiggle and leaking water when pressurized continued. The unit works perfectly well, I just cannot get the hose connector to stop leaking no matter how tight or many washers I installed. I noticed others have this complaint in their reviews, so I guess I was forewarned. Apparently the design doesn't allow a leak free hose connection. It doesn't leak at the body connection point, it's behind the hose screw-on point. Not sure what the fix would be since I've tried everything and it seems to be tight (other than the water streaming out from behind)
Other than that the washer does a really decent job for an electric powered washer. Since the job it does is a wet environment I'll just have to put up with the leaking. My wand falls out of the holder like everyone's too...
Other than that the washer does a really decent job for an electric powered washer. Since the job it does is a wet environment I'll just have to put up with the leaking. My wand falls out of the holder like everyone's too...
I would recommend this to a friend!
Written by a customer while visiting greenworkstools.com
Posted by: Dave Mock
from Largo. Florida
Gender:Male
Verified Purchase:Yes
So far, so good. I've only used the pressure washer twice, but it's done everything I've expected. It's very quiet. The design keeps it stable on the ground. I'm checking to see if there is a longer hose, or extension hose available.
I would recommend this to a friend!
Written by a customer while visiting greenworkstools.com
Customer Rating
2
Cuts off frequently
on May 14, 2022
Posted by: GinArden
from Arden, NC
Gender:Male
I just bought a Greenworks Pro 2300 pressure washer today. Overall, it works well, but the engine keeps cutting off, from ever 20 seconds to every 2 minutes. Restarts again as soon as I release and squeeze the handle. I assume something is defective, but I just spent 40 minutes on hold, trying to call technical support, despite being in, "position 1". Please let me know how to fix this problem. I would hate to have to return it unnecessarily.
Response from greenworkstools.comBy Greenworks, Greenworks Customer Support, May 16, 2022
Hello,
There are a few factors that could cause these reactions such as excess air in the pump or a clogged/faulty nozzle. See all troubleshooting options below.
Purge Air from Pressure Washer
Set up the unit as per usual and ensure you are not using an extension cord. Remove any nozzle that may be connected at the end of the wand. Make sure that you have a green light on the GFCI on the power cord. Turn your garden hose on but leave the pressure washer turned OFF. With the pressure washer turned off, squeeze on the trigger for about 3 minutes – allowing the water to run through the unit at no pressure. In doing so, you are bleeding the unit out of any air that may be stuck in the pump. After 3 minutes, turn the unit on. Reinstall one of your clean nozzles and continue using the unit. At this stage, if the unit shuts off when a nozzle is installed be sure to try all nozzles. A faulty nozzle may cause the unit to shut down.
Additional components to check:
• Ensure a nozzle is connected. Be sure to try all nozzles.
• Ensure that the water source is fully opened and is at least 60PSI (Refer to: Does my water source have to be of a certain PSI to run the unit properly?)
• Check that there is at least 10' of unrestricted garden hose between the hose connection and the unit, any kinks will prevent the flow of water from going into the unit and prevent proper pressure.
• For best results, use a 1” (25 mm) or 5/8” (16 mm) garden hose.
• Check that the water inlet is not clogged. Disconnect the garden hose, remove the filter and rinse with warm water.
There are a few factors that could cause these reactions such as excess air in the pump or a clogged/faulty nozzle. See all troubleshooting options below.
Purge Air from Pressure Washer
Set up the unit as per usual and ensure you are not using an extension cord. Remove any nozzle that may be connected at the end of the wand. Make sure that you have a green light on the GFCI on the power cord. Turn your garden hose on but leave the pressure washer turned OFF. With the pressure washer turned off, squeeze on the trigger for about 3 minutes – allowing the water to run through the unit at no pressure. In doing so, you are bleeding the unit out of any air that may be stuck in the pump. After 3 minutes, turn the unit on. Reinstall one of your clean nozzles and continue using the unit. At this stage, if the unit shuts off when a nozzle is installed be sure to try all nozzles. A faulty nozzle may cause the unit to shut down.
Additional components to check:
• Ensure a nozzle is connected. Be sure to try all nozzles.
• Ensure that the water source is fully opened and is at least 60PSI (Refer to: Does my water source have to be of a certain PSI to run the unit properly?)
• Check that there is at least 10' of unrestricted garden hose between the hose connection and the unit, any kinks will prevent the flow of water from going into the unit and prevent proper pressure.
• For best results, use a 1” (25 mm) or 5/8” (16 mm) garden hose.
• Check that the water inlet is not clogged. Disconnect the garden hose, remove the filter and rinse with warm water.
Written by a customer while visiting greenworkstools.com
Posted by: KDunn
from Bartlett Tennessee
Gender:Female
Verified Purchase:Yes
Everything about this product is wonderful! Highly recommend!
I would recommend this to a friend!
Written by a customer while visiting greenworkstools.com
Posted by: Andrew from Iowa
from West Des Moines iowa
Gender:Male
Verified Purchase:Yes
Once it gets going works great; have had slight trouble when getting started, the pressure ramps up then has stalled out. I’ve had to reset by unplugging and then it worked fine. Just the right pressure for vehicle washing.
I would recommend this to a friend!
Written by a customer while visiting greenworkstools.com
Posted by: Dmarsh
from Reno, NV
Gender:Male
Verified Purchase:Yes
Power washer works well. Other than the slight delay in time for pressure to build up, I have no complaints.
I would recommend this to a friend!
Written by a customer while visiting greenworkstools.com
Customer Rating
2
Delayed start, not for car washing
on June 4, 2022
Posted by: llz0816
from Chesapeake, VA
Gender:Male
Purchased this around December. It has been sitting in my garage for about 5 months before I take it out for a first use. Wish I test it earlier so I could return it in time. I got it mainly for car wash, there’s deal break issue for me due to a few second delay that slowly boost the machine to full power. It’s annoying and problematic when you use it with a foam cannon. Every time you stop the trigger, the delay start will make a mess with foam cannon, which kinda force me to do the foaming process in one shot. It’s just annoying and bothersome to me. Maybe not a big deal for others.
No, I would not recommend this to a friend.
Response from greenworkstools.comBy Greenworks, Customer Care, June 7, 2022
Hello llz0816,
We are sorry to hear about your experience when using this pressure washer. It sounds like you will need to contact us directly some further information would be required to be better assist. Please allow our team to gather some further details so that we can help find a resolution for you. We kindly ask that you give us a call at 1-888-909-6757 (1-888-90WORKS). All we ask that you have access to the unit so that we can complete troubleshooting with you and gather necessary unit information.
We are sorry to hear about your experience when using this pressure washer. It sounds like you will need to contact us directly some further information would be required to be better assist. Please allow our team to gather some further details so that we can help find a resolution for you. We kindly ask that you give us a call at 1-888-909-6757 (1-888-90WORKS). All we ask that you have access to the unit so that we can complete troubleshooting with you and gather necessary unit information.
Written by a customer while visiting greenworkstools.com