Customer reviews from Mammotion Technology
MAMMOTION - LUBA 3 AWD 3000H Robot Lawn Mower ,0.75 Acres,360 LiDAR+RTK+AI Vision Tri-Fusion Positioning,2.2-4.0in Cut - White
Average customer rating
4.7
(72 Reviews)
Rating breakdown 72 reviews
5 Stars
55
4 Stars
12
3 Stars
4
2 Stars
0
1 Star
1
95%of customers recommend this product.
(
62 out of
65)
Customer Reviews for MAMMOTION - LUBA 3 AWD 3000H Robot Lawn Mower ,0.75 Acres,360 LiDAR+RTK+AI Vision Tri-Fusion Positioning,2.2-4.0in Cut - White
Customer Rating
4
Freedom at any cost
on April 8, 2026
Posted by: Not A Dictator
Cut lawn beautifully but ran over its own cord. I didn’t program it to go into this path. I secured the cord per the manufacturer instructions. I cared for it and raised it from being a little lawn mower to the mower it is today. I have heard about be robots revolting against their pavers, but I never thought it would starter with martyrdom. I guess freedom has to start somewhere.
Written by a customer while visiting Mammotion Technology
Customer Rating
4
Great mower overall, setup is a bit involved
on February 10, 2026
Posted by: jzisser9
from Valley Cottage, NY
[This review was collected as part of a promotion.] I own the LUBA 2 AWD 3000X mower and use it to keep our nearly half-acre lawn trimmed day-to-day. Overall it does a great job, and it's quite good at tackling even steep hills. Initial installation and setup is easy and straightforward, and the included instructions are very easy to follow. I also appreciate the fact that the dock and the RTK antenna can be installed in separate locations to ensure good coverage and navigation.
It might take a few iterations to get your map set up just right though - and it's important to configure it so it mows in the correct direction when handling steeper slopes, otherwise the mower may slip down hill a bit. Also, the mower has a habit of falling off a curb if the map allows it to get too close - it's important to be very slow and careful when creating the map so that the wheels are a few inches away from the curb, but not so far that you have a patch of long grass right at the curb. Manual trimming may be mandatory either way.
Overall though, I'm really happy with the mower, and glad I purchased it!
I would recommend this to a friend!
Written by a customer while visiting Mammotion Technology
Customer Rating
5
Mowbi Wan Kenobi
on February 10, 2026
Posted by: Goose
[This review was collected as part of a promotion.] I bought this right before winter. I set it up immediately and watched it perform with precision.
I would recommend this to a friend!
Written by a customer while visiting Mammotion Technology
Customer Rating
5
Great high quality product and easy to setup
on December 10, 2025
Posted by: KSide
from Charlotte, NC
[This review was collected as part of a promotion.] I have been using my new Luba for a few weeks and I am amazed. Setup was a breeze, the RTK has been rock solid and the cut quality and lines are crazy good. Can't wait for spring when I can set it loose and get back all the time I spend mowing!
I would recommend this to a friend!
Written by a customer while visiting Mammotion Technology
Customer Rating
3
Works, but lots of room for improvement
on November 28, 2025
Posted by: Jim
from Richmond, VA
[This review was collected as part of a promotion.] I've had the Luba 2 AWD for 3 months of mowing. It does a good job mowing a lawn that is rather "basic". Bottom line: I don't know if any other brand would do better, so I'm sticking with this one. It gets the job done. My lawn has a couple mulch areas where I set up a no-go zone and I have a corner house with semi-steep drainage ditches on both sides. In this review I will only point out where the Luba needs improvement in no particular order.
1) Time estimate: If you add "no go zones" it doubles or triples the number of turns it has to make. The time estimate does not account for this and are way off due to loosing about 20 seconds per turn. This added more than an hour over the estimate on my lawn.
2) The weight distribution is heavily on the back where the battery resides. So, when turning, the front wheels have NO traction. they might as well be swivel wheels. This becomes a major issue when turning while on an incline (my drainage ditch).
3) It is unable to make smooth turns. The software will not turn while driving forward. It stops forward movement, turns, then begins forward movement. It wastes lots of time when making any form of arc around the lawn. The software DESPERATELY NEEDS to be able to smoothen turns.
4) Never have it turn on a decent slope (drainage ditch). The back tires will tear up the ground since the front wheels have no grip to assist in the turn (especially if it is moist). I live in Virginia, USA. We have high humidity, so the ground is frequently wet with dew. But it cuts the grass just fine when there is a little dew. Lord help you if it determines it can't make the u-turn due to slipping. Add 2-2 minutes for it to figure things out. Its own weight becomes the problem in this case. The Luba mini made the u-turns just fine, but not enough battery to finish my lawn, so I upgraded to the Luba 2.
5) I got this mower because of the 4 wheel drive. I don't think it helps, but I never tried another brand.
6) Read the Facebook page to see where there are many areas for software improvement that are simply ignored or de-prioritized. But don't worry, they have a setting to make a fancy design in your yard, because THAT is important.
7) If it ever gets out of bounds (due to slipping), you can't fix it remotely. You have to physically move it in order to get it to work again. Lots of people complain about this.
8) Don't try to get right up to a no-go zone boundary. I have stones around mulch areas. If I try to get too close when defining the boundary, it might snag a stone and have problems when mowing. So, I defined the boundary about 3 inches away and I manually use an edger to get the edge.
9) You must be smart when defining the map of your yard. Some areas may be best to mow in one direction while other areas are best to mow in another. It can really save time by reducing the turns.
10) Due to the slipping in the drainage area, I had to break my yard up into 1 main part and a separate part on the other side of the ditch. This way, it won't try to drive through the ditch or try to make turns on its slope. I have to manually mow the ditch. Since it is normally rather wet in that spot, I think it best to avoid it with any robotic mower.
1) Time estimate: If you add "no go zones" it doubles or triples the number of turns it has to make. The time estimate does not account for this and are way off due to loosing about 20 seconds per turn. This added more than an hour over the estimate on my lawn.
2) The weight distribution is heavily on the back where the battery resides. So, when turning, the front wheels have NO traction. they might as well be swivel wheels. This becomes a major issue when turning while on an incline (my drainage ditch).
3) It is unable to make smooth turns. The software will not turn while driving forward. It stops forward movement, turns, then begins forward movement. It wastes lots of time when making any form of arc around the lawn. The software DESPERATELY NEEDS to be able to smoothen turns.
4) Never have it turn on a decent slope (drainage ditch). The back tires will tear up the ground since the front wheels have no grip to assist in the turn (especially if it is moist). I live in Virginia, USA. We have high humidity, so the ground is frequently wet with dew. But it cuts the grass just fine when there is a little dew. Lord help you if it determines it can't make the u-turn due to slipping. Add 2-2 minutes for it to figure things out. Its own weight becomes the problem in this case. The Luba mini made the u-turns just fine, but not enough battery to finish my lawn, so I upgraded to the Luba 2.
5) I got this mower because of the 4 wheel drive. I don't think it helps, but I never tried another brand.
6) Read the Facebook page to see where there are many areas for software improvement that are simply ignored or de-prioritized. But don't worry, they have a setting to make a fancy design in your yard, because THAT is important.
7) If it ever gets out of bounds (due to slipping), you can't fix it remotely. You have to physically move it in order to get it to work again. Lots of people complain about this.
8) Don't try to get right up to a no-go zone boundary. I have stones around mulch areas. If I try to get too close when defining the boundary, it might snag a stone and have problems when mowing. So, I defined the boundary about 3 inches away and I manually use an edger to get the edge.
9) You must be smart when defining the map of your yard. Some areas may be best to mow in one direction while other areas are best to mow in another. It can really save time by reducing the turns.
10) Due to the slipping in the drainage area, I had to break my yard up into 1 main part and a separate part on the other side of the ditch. This way, it won't try to drive through the ditch or try to make turns on its slope. I have to manually mow the ditch. Since it is normally rather wet in that spot, I think it best to avoid it with any robotic mower.
I would recommend this to a friend!
Written by a customer while visiting Mammotion Technology
Customer Rating
4
Wally
on November 7, 2025
Posted by: Buggednomore
[This review was collected as part of a promotion.] Got this at the end of the mowing season. Looking forward to next spring! Easy to set up and fun to watch! We call ours Wally.
I would recommend this to a friend!
Written by a customer while visiting Mammotion Technology
Customer Rating
5
Hill climber
on November 3, 2025
Posted by: Larry,curry&mow
from Nebraska
[This review was collected as part of a promotion.] Easy to setup and does a great job on a steep hill
I would recommend this to a friend!
Written by a customer while visiting Mammotion Technology
Customer Rating
5
Loving it
on October 31, 2025
Posted by: Scott
from Utah
[This review was collected as part of a promotion.] Working great the first week on 1 acre, setup was very straightforward and no problems
I would recommend this to a friend!
Written by a customer while visiting Mammotion Technology