Customer Reviews for Peak Design - Micro Clutch Hand Strap - Black
Customer Rating
2
Nikon Z7 FTZ issue
on August 4, 2023
Posted by: dcap
There is a problem with the design of the L-Plate and the Nikon ZZ when using the FT adapter. Access to the tool housing is blocked by the adapter. The bottom of the micro clutch plate and the FTZ adapter are at the same level making it impossible to remove the tool when the FTZ adapter is attached to the camera. The only way to get to the tool in order to access the camera battery is to first remove the FTZ adapter from the camera, access the tool to loosen the plate and then you can get to the battery enclosure. The reverse process is to replace the FTX adapter, move the micro clutch plate to its ideal position, tighten the plate with the tool, and then slide the tool between the plate and the adapter. The magnet will pull the tool in place. This is not a good design - perhaps a future design for the L-plate would be to put the tool on the opposite side of its present location. It's possible the straight plate may be better suited but it would still have to be on in reverse orientation so the tool faces the back of the camera. The only other way around this is to carry the tool separately which then makes it easy to lose or forget and then you cannot get to the camera battery. This is a shame because otherwise it is a beautiful piece of machined work.
No, I would not recommend this to a friend.
Response from Peak DesignBy PD Team, PD Team, August 11, 2023
Thank you for your feedback and sorry for the frustration here! We're sorry to hear the micro clutch doesn't work with your set up as expected! We tried hard to accommodate as many makes and models as possible but unfortunately, there are a few out there that just don't quite work or require a little bit of a "hack" to work most optimally.
A suggestion from the design team on this would be to he buy a spare flat tool and either pocket it or drill a hole on the very end of the tool handle and put it on your keychain.
Really love the design, and this is definitively something I am going to keep on my camera at all times. I liked the original clutch a lot, but for a mirrorless camera (Canon M50 and now RP), it was too big. This product is really perfect for my RP.
Previously I have switched between the old clutch, a Slide Lite or a Leash depending on lens setup, but this is going to. be on my camera at all times from now on. The bottom fits very neatly with my camera, and the strap is easy to ignore if you don't need it for a particular shoot.
The advertising said for mirrorless, so I bought it for Nikon Z 8-BIG MISTAKE It is a well made quality product and on a smaller mirrorless body I assume it would work, but I can't get my fingers in the space provided-not enough room for even my small fingers-got the clutch instead. Peak was very helpful in working with me to get me something that would work for this body
I have been happily using my micro clutch for several weeks now. The clutch helps to give me a very secure grip on my Nikon Z50. It's compact, lightweight yet sturdy. I had worried at first that it would unduly interfere with access to my battery and SD card, but have in fact found it so easy to rotate out of the way that I don't even think about it now.
The installation guide is just a guide, extra hack can be needed Personal tips: If you found the silicone sleeve is not perfect fit, try rotate the plate a little bit or try to install split ring even your camera have slot attachment instead of a eyelet, something magical can happen:)
Got an I-Plate during the Kickstarter for my Q3. It works great with the Leica thumb grip to give a secure single-hand grip. Build quality is up to peak’s usual fine standards.
One general con: strap adjustment is difficult. The holes are very small relative to the post you fit them over. This results in a very secure fit once done, but is a bit of a bear to get set the first time if you have big hands and short nails like I do.
One Q3 specific con: you will not be able to access the SD card without removing the baseplate _and_ screw, as the location of the tripod mount on the Q3 means the baseplate overhangs. This is a minor con given the Q3 has USB file transfer unlike earlier models, but is probably why the I-Plate was rated non-compatible with the Q3 unlike the Q2. It otherwise works perfectly, and you can get at the battery with only removing the baseplate as intended.
Another really great little add-on for my gear. Super low profile and exactly what I was hoping it would be for my little camera. Makes it a lot less likely that I'm going to inadvertently test its ability to survive a drop. Beautifully made and solid.