Customer reviews from greenworkstools.com
Greenworks - 3000 PSI Pressure Washer (2.0 GPM Max) with Foam Cannon - Powerful Enough to Remove Pesky Dirt - Green
Average customer rating
4.7
(2,025 Reviews)
Rating breakdown 2,025 reviews
5 Stars
1,601
4 Stars
291
3 Stars
47
2 Stars
28
1 Star
58
94%of customers recommend this product.
(
1,701 out of
1,801)
Customer Reviews for Greenworks - 3000 PSI Pressure Washer (2.0 GPM Max) with Foam Cannon - Powerful Enough to Remove Pesky Dirt - Green
Customer Rating
1
Used once and now broke
on November 27, 2021
Posted by: Guy24
from Houston TX
I used this pressure washer once. It sat in the garage for a few months and now water won't flow through it. Motor turns on and nothing come out the outlet even with the hose disconnected
No, I would not recommend this to a friend.
Response from greenworkstools.comBy Greenworks, Customer Care, November 29, 2021
Hello Guy24,
Sorry to hear of the issue you are experiencing with the pressure washer.
It sounds as though your nozzles may be clogged or there is some air trapped in the unit, these are common issues. With the following troubleshooting, this should be resolved! Please be sure to follow closely as these steps are not as effective when altered.
1) To clean the nozzles, soak all your nozzles in a half and half mixture of warm water and white vinegar. Soak all the nozzles for about an hour and then proceed to poke your nozzle cleaning tool or paper clip through the end of the nozzle hole to poke out any debris. After you have done this, rinse them with warm water. Your nozzles will now be free of any obstructions causing the unit to malfunction.
2) Purge any excess air from the pump. Set up the unit as per usual and ensure you are not using an extension cord. Remove any nozzle that may be connected at the end of the wand. Make sure that you have a green light on the GFCI on the power cord. Turn your garden hose on but leave the pressure washer turned OFF. With the pressure washer turned off, squeeze on the trigger for about 3 minutes – allowing the water to run through the unit at no pressure. In doing so, you are bleeding the unit out of any air that may be stuck in the pump. After 3 minutes, turn the unit on. If it is running, reinstall one of your clean nozzles and continue using the unit.
3) Ensure that the water source is fully opened and is at least 60PSI.
4) There should be 10' of unrestricted garden hose between the hose connection and the unit, any kinks will prevent the flow of water going into the unit and prevent proper pressure.
If you are still having trouble, please submit an email using the customer contact page on our website or give us a call at 1-888-909-6757 (1-888-90WORKS).
Sorry to hear of the issue you are experiencing with the pressure washer.
It sounds as though your nozzles may be clogged or there is some air trapped in the unit, these are common issues. With the following troubleshooting, this should be resolved! Please be sure to follow closely as these steps are not as effective when altered.
1) To clean the nozzles, soak all your nozzles in a half and half mixture of warm water and white vinegar. Soak all the nozzles for about an hour and then proceed to poke your nozzle cleaning tool or paper clip through the end of the nozzle hole to poke out any debris. After you have done this, rinse them with warm water. Your nozzles will now be free of any obstructions causing the unit to malfunction.
2) Purge any excess air from the pump. Set up the unit as per usual and ensure you are not using an extension cord. Remove any nozzle that may be connected at the end of the wand. Make sure that you have a green light on the GFCI on the power cord. Turn your garden hose on but leave the pressure washer turned OFF. With the pressure washer turned off, squeeze on the trigger for about 3 minutes – allowing the water to run through the unit at no pressure. In doing so, you are bleeding the unit out of any air that may be stuck in the pump. After 3 minutes, turn the unit on. If it is running, reinstall one of your clean nozzles and continue using the unit.
3) Ensure that the water source is fully opened and is at least 60PSI.
4) There should be 10' of unrestricted garden hose between the hose connection and the unit, any kinks will prevent the flow of water going into the unit and prevent proper pressure.
If you are still having trouble, please submit an email using the customer contact page on our website or give us a call at 1-888-909-6757 (1-888-90WORKS).
Written by a customer while visiting greenworkstools.com
Customer Rating
5
3,000 PSI !!! No fuel or sparks plugs
on December 10, 2021
Posted by: Jestar1
from Rib Mountain WI
Gender:Female
I have been utilzing this power washer in many ways. It truly does have a have 3,000 psi...you used to have to get a gasoline powered one to get anything over 1,800 . I have used it on my truck, to clean the cedar logs of my home, knocking off hornet's nests ,from a afe distance.
I would recommend this to a friend!
Written by a customer while visiting greenworkstools.com
Customer Rating
5
3000 psi Pressure Washer
on March 22, 2022
Posted by: John Dove
from Cypress tx
Gender:Male
I bought this to add to my all electric outdoor power tools. Had a 3300 psi Simpson with Honda engine, worked great but very noisy, and the disadvantage of having to store gasoline. Have not used as yet but know I will not be dissolved. Stores in very little space, and very compact compared to the gas one I previously owned. Bought this 3000 psi green works pressure washer as it’s rating was very high.
I would recommend this to a friend!
Written by a customer while visiting greenworkstools.com
Customer Rating
5
EASY TO USE AND GREAT RESULTS
on May 29, 2022
Posted by: JOEBOB11
from BIRMINGHAM,AL
Gender:Male
THE GREENWORKS PRO 3000 WAS EASY TO USE AND I HAD GREAT RESULTS. DECK IS 25 YEARS OLD AND WAS GREY AS COULD BE. I USED THE GREENWORKS 3000 AND IT BROUGHT IT BACK TO LIFE . MY NEIGHBORS THOUGHT I REPLACED MY DECK.
I would recommend this to a friend!
Written by a customer while visiting greenworkstools.com
Posted by: volfan
from Chattanooga, TN
Gender:Male
Verified Purchase:Yes
Have used several times and I am very impressed. Power is great and had no issues at all. Very easy to move around the house using the large tires. LOVE the hose that comes with this as it is much more flexible than any hose I have used before.
I would recommend this to a friend!
Response from greenworkstools.comBy Greenworks, Customer Care, June 16, 2022
Hello volfan,
We are glad to hear you are enjoying the product! If it ends up that you are having an issue with the pressure washer, please contact our Customer Support at 1-888-909-6757 (1-888-90WORKS), and we would be happy to assist you further in remedying an issues.
Thank you for your feedback!
We are glad to hear you are enjoying the product! If it ends up that you are having an issue with the pressure washer, please contact our Customer Support at 1-888-909-6757 (1-888-90WORKS), and we would be happy to assist you further in remedying an issues.
Thank you for your feedback!
Written by a customer while visiting greenworkstools.com
Customer Rating
1
Unit completely dead after 4 uses in 5 months.
on September 27, 2022
Posted by: Bemo
from Sugar Land, Texas
Gender:Male
Unit completely died after nearly a handful of uses in as many months.
No, I would not recommend this to a friend.
Response from greenworkstools.comBy Greenworks, Customer Care, September 27, 2022
Hello Bemo,
We are sorry to hear that you are experiencing an issue with your pressure washer. Unfortunately, your review is not detailed enough for us to know what the issue is, but we will try to cover all bases.
Here you will find some troubleshooting suggestions for you to try.
Cleaning Obstructed Nozzles: To clean the nozzles, soak all your nozzles in a half and half mixture of warm water and white vinegar. Soak all the nozzles for about an hour and then proceed to poke your nozzle cleaning tool or paper clip through the end of the nozzle hole to poke out any debris. After you have done this, rinse them with warm water. Your nozzles will now be free of any obstructions causing the unit to malfunction.
Removing Air from The Line / Bleeding Out the Unit: Purge any excess air from the pump. Set up the unit as per usual and ensure you are not using an extension cord. Remove any nozzle that may be connected at the end of the wand. Make sure that you have a green light on the GFCI on the power cord. Turn your garden hose on but leave the pressure washer turned OFF. With the pressure washer turned off, squeeze on the trigger for about 3 minutes – allowing the water to run through the unit at no pressure. In doing so, you are bleeding the unit out of any air that may be stuck in the pump. After 3 minutes, turn the unit on. If it is running, reinstall one of your clean nozzles and continue using the unit.
Lastly, ensure that the water source is fully opened and is at least 60 PSI. There should be 10' of unrestricted garden hose between the hose connection and the unit, any kinks will prevent the flow of water going into the unit and prevent proper pressure.
Please note this product has a 3-year warranty from the date of purchase.
If you have tried these steps and are still experiencing issues, please contact Greenworks at 1-888-909-6757 (1-888-90WORKS).
We are sorry to hear that you are experiencing an issue with your pressure washer. Unfortunately, your review is not detailed enough for us to know what the issue is, but we will try to cover all bases.
Here you will find some troubleshooting suggestions for you to try.
Cleaning Obstructed Nozzles: To clean the nozzles, soak all your nozzles in a half and half mixture of warm water and white vinegar. Soak all the nozzles for about an hour and then proceed to poke your nozzle cleaning tool or paper clip through the end of the nozzle hole to poke out any debris. After you have done this, rinse them with warm water. Your nozzles will now be free of any obstructions causing the unit to malfunction.
Removing Air from The Line / Bleeding Out the Unit: Purge any excess air from the pump. Set up the unit as per usual and ensure you are not using an extension cord. Remove any nozzle that may be connected at the end of the wand. Make sure that you have a green light on the GFCI on the power cord. Turn your garden hose on but leave the pressure washer turned OFF. With the pressure washer turned off, squeeze on the trigger for about 3 minutes – allowing the water to run through the unit at no pressure. In doing so, you are bleeding the unit out of any air that may be stuck in the pump. After 3 minutes, turn the unit on. If it is running, reinstall one of your clean nozzles and continue using the unit.
Lastly, ensure that the water source is fully opened and is at least 60 PSI. There should be 10' of unrestricted garden hose between the hose connection and the unit, any kinks will prevent the flow of water going into the unit and prevent proper pressure.
Please note this product has a 3-year warranty from the date of purchase.
If you have tried these steps and are still experiencing issues, please contact Greenworks at 1-888-909-6757 (1-888-90WORKS).
Written by a customer while visiting greenworkstools.com
Customer Rating
5
Greenworks gets it right
on April 23, 2023
Posted by: dte230
from atlanta
Gender:Male
I pressure have the 2300 pro washer and it's great. I did have a slight problem and Greenworks was all over it. They corrected it immediately. After the sale, there is nothing left but support and they get an A+
Pros: Easy to Use, Quiet, Durable, Powerful
I would recommend this to a friend!
Written by a customer while visiting greenworkstools.com
Customer Rating
5
Just what I needed
on September 27, 2023
Posted by: jis14
from West Bountiful, UT
Gender:Male
[This review was collected as part of a promotion.] Bought this a week ago to clean off the garage door, wood, and stucco. Initial setup was easy. The nozzle options were very nice to have. Cleaned off the materials just like what I was hoping for.
I would recommend this to a friend!
Written by a customer while visiting greenworkstools.com